There are following several type for choice
  CCFW(AD)-1000×12000CCFW(AD)-1600×12000
   CCFW(AD)-2000×12000CCFW(AD)-2600×12000
   CCFW(AD)-3000×12000CCFW(AD)-4000×12000
This FRP(fibre reinforced plastic) RMP (reinforce mortar pipe)pipe product line consists of:
  　    -Liner Making Machine
　　 -Winding Machine
　　 -Curing Station
　　 -Calibration Machine
　　 -Gantry Ejection Machine
　　 -System of Mixing Resin
      Technical capability of product line
Main technical data of Liner making machine:
　．Spindles averaged speed 50m/min
　．Main axis and carriage is timing with
　　frequency conversion
　．Feeding-resin system:Flow:0-20kg/min Flow is
　　regulated with frequency conversion
　．Form of drive: drive by rack
This machine is specially used in the FRP RMP pipe product line for making the inner liner of pipe.
　．Winding angle: ≥45°≤90°
　． Speed of draw-fibre: ≤130m/min
　． Widh of yarn: 4-200mm
　． Form of winding: screw or round（change 　automatically）
　． Form of control: manual, autoloading, automatic
　Form of draw-fibre: linea
　． The winding length as L, the width of reinforce mortar roving   　as B, the winding angle as a, and 　the length of resting on the 　end as c. When the 　winding length L is fixed, any two 　parameters of 　the other three can be fixed.
　． The top or the end of a pipe can be winded as 　the zero 　point of winding.
　．This machine can directly change from the form 　winding by 　round with single layer to the form 　winding by screw.
　． This machine can pour mortar, flow-in resin, 　reinforce 　mortar in each time, and it can 　continuous reinforce mortar to 　and fro.
　．The feeding-resin flow of feeding-resin system 　for reinforce 　motar and pouring-resin is 　45kg/min(timing with frequency 　conversion). The 　thickness of reinforce mortar each time come 　up to 　3-20mm.The thickness is not influenced by man-made 　and too-heavy of mould.
This machine is the best important equipment of the FRP RMP pipe product line for winding and making reinforce mortar on the structural layer of a FRP pipe.
Main technical data of the curing station
　．Speed of main axis: 5rpm
　． Spindles averaged speed 50m/min
　． It can calibrate 1/32 taper and the joint of double seal 　ring type-O
　． Form of dust collection: water tank (moveable)
This machine is specially used in the FRP RMP pipe product line for making the inner liner layer or structural layer of pipe for solidifing.
Main technical data of the calibration machine
　．Can calibrate pipe mould made by FRP
　．Mode of speed controlling: timing with frequency 　conversion
This machine is specially used in the FRP RMP pipe product line for calibrating the joint of FRP pipe.
Main technical data of the gantry ejection machine:
　． Ejection force: 70T
　． Traction force of windlass:5T
　． Ejection big car and tractor can step 　automatically
This machine is specially used in the FRP RMP pipe product line for ejection the FRP pipe.
Main technical data of system of mixing resin
　． Mixing tin: more than 1.2m3
This machine is specially used in the FRP RMP pipe product line for supply with pre-mixing resin added hardener for the FRP RMP pipe product line.

There are following several type for choice    
　 CCFW(AD)-2×2-300×6000 CCFW(AD)-2×1-600×12000

This FRP(fibre reinforced plastic) RMP (reinforce mortar pipe)pipe product line consists of

　 -Winding Machine
　 -Curing Station
　 -Calibration Machine
　 -mandrel extractors
　 -System of Mixing Resin

Main technical dataof Winding machine:

　．Accuracy of draw-fiber: ±0.5mm
　．Winding angle: ≥45°≤90°Speed of draw-fibre: 　≤100m/min
　． Form of winding: screw or round（change 　automatically）
　． Form of control: manual, autoloading, automatic
　． Form of draw-fibre: linea
　． Form of reinforce-mortar: einforce mortar at 　obligue-　under-　side
　． Form of drive: drive by rack
　． The winding length as L, the width of reinforce 　mortar 　roving as B, the winding angle as a, and 　the length of 　resting 　on the end as c. When the 　winding length L is 　fixed, any two 　parameters of 　the other three can be 　fixed.
　． The top or the end of a pipe can be winded as 　the zero 　point of winding.
　． This machine can directly change from the form  　winding 　by round with single layer to the form 　winding by screw.
  . This machine can pour mortar, flow-in resin, 　reinforce 　mortar in 　each time, and it can 　continuous reinforce mortar 　to and fro.
　． The thickness of reinforce mortar each time 　come up to 　3-　10mm.

Brief introduction of the FRPcontainer product line:

　There are following several type for choice
　CCFW-2×1-2000×12000CCFW-2×1-4000×12000

This FRP(fibre reinforced plastic) container product line consists of:

　-Liner Making Machine of container
　 -Winding Machine
　 -butt joint device of container Liner
　 -auxiliarydevice
　 -System of Mixing Resin

Main technical dataof Winding machine:
  ．Accuracy of draw-fiber: ±0.5mm
　．Winding angle: ≥45°≤90°
　．Speed of draw-fibre: ≤100m/min
　．Widh of yarn: 4-200mm
　．Form of winding: screw or round（change ．．．   　．　automatically）
　．Form of control: manual, autoloading, automatic
　．Form of draw-fibre: linea
　．Form of drive: drive by rack
　．The winding length as L, the width of reinforce 　mortar roving 　as B, the winding angle as a, and 　the length of resting on the end 　as c. When the 　winding length L is fixed, any two parameters of 　the 　other three can be fixed.
　．The top or the end of a pipe can be winded as 　the zero point of 　winding.
　．This machine can directly change from the form 　winding by 　round with single layer to the form 　winding by screw.