There are following several type for choice
  　　CCFW-2×1-10000×12000
This FRP(fibre reinforced plastic) container product line consists of:
　　 -locale Winding Machine
　 　-System of Mixing Resin
Main technical dataof Winding machine:
　．Accuracy of draw-fiber: ±0.5mm
　．Winding angle: ≥45°≤90°
　．Speed of draw-fibre: ≤100m/min
Widh of yarn: 4-200mm
　．Form of winding: screw or round（change automatically）
　． Form of control: manual, autoloading, automatic
　． Form of draw-fibre: linea
　．Form of reinforce-mortar: einforce mortar at obligue-under-side
　． Form of drive: drive by rack
　． The winding length as L, the width of reinforce mortar roving as B,
　the winding angle as a, and the length of resting on the end as c. When
　the winding length L is fixed, any two parameters of the other three can 　be　fixed.
　．The top or the end of a pipe can be winded as the zero point of 　winding.
　．This machine can directly change from the form winding by round with 　single layer to the form winding by screw.
Two axis、Three axis、Four axis High Accuracy
Winding Machine
　Standardconfiguration: 1、2-spindle or 2、3、4-axisDesigned 　specifically for Multiple spindlesMain technical dataof Winding 　machine:
Mandrel Rotation
　．Winding diameter
　．Two spindle：500㎜(Max)
　．Single spindle：Any
　．Winding length： Any
　．Winding angle：8o-89o
　．Effective speed range：0-120 rpm
　．Accuracy(Angular Deviation)：﹤0.1deg
Horizontal carriage
　．Maximum speed：60m/min
　．Accuracy(Repeatability)：±0.1 ㎜
Crossfeed carriage
　．Maximum：36m/min
　．Accuracy(Repeatability)：±0.1 ㎜
Eye rotation
　．Stroke ：360°continuous
　．Maximum speed：150rpm

There are following several type for choice
　　 CCFW-2×1-25000×8000
This FRP(fibre reinforced plastic) container product line consists of:
　 -locale vertical Winding Machine
　 -System of Mixing Resin

Main technical dataof Winding machine:
　 ．Accuracy of draw-fiber: ±0.5mm
　．Winding angle: ≥60°≤90°
　．Speed of draw-fibre: ≤100m/min
　．Widh of yarn: 4-300mm
　．Form of winding: screw or round（change automatically）
　．Form of control: manual, autoloading, automatic 　
　 ．Form of 　draw-fibre: linea
　．Form of reinforce-mortar: einforce mortar at obligue-under-　side
　．Form of drive: drive by rack
　． The winding length as L, the width of reinforce  mortar 　roving as B, the winding angle as a, and the length of resting on 　the end as c. When the winding length L is fixed, any two 　parameters of the other three can be fixed.

Hydraulic Pressure Test Equipment
　　
　　 There are following several type for choice

DN1000×12000DN2000×12000 DN3000×12000
Main technical data of the hydraulic pressure test equipment
 　． testing pressure: 20KG/CM2
　 ．Main water pump: Flow: 170M3/h
 　． Booster pump:Flow: 6M3/hLift: 207m H2o

This machine is specially used intesting pressure of the FRP pipe for checking the pipe or the joint of pipe whether or not leakage.